High-country-tek DVC80 Bedienungsanleitung PDF herunterladen (Seite 53)

P/N: 021-00154, Rev. A.6 - updated for V4.7 Tools Page | 53

from 100% to 0%)

Name.Frequency Set PWM frequency 0 to 1000 for 0 to 100hz

Name.Dutycycle Ser PWM dutycycle 0 to 1023 for 0 to 100%

Name.Freqerror Returns error 1 = Frequency error,

2 means duty cycle error

HSEvenName Set the Bang-bang Coil to On or Off Off, On

HSEven#Name.Short Get the Coil Flag for Short Status Off [Coil Ok], On [Coil

Short]

HSEven#Name.Open Get the Coil Flag for Open Status Off [Coil Ok], On [Coil

Open]

HSOddName Set the Bang-bang Coil to On or Off Off, On

HSOdd#Name.OpenDisable

Set the Disable Coil Open Detection 0 [Enabled], 1 [Disabled]

HSOdd#Name.Short Get the Coil Flag for Short Status Off [Coil Ok], On [Coil

Short]

HSOdd#Name.Open Get/Set the Coil Flag for Open Status Off [Coil Ok], On [Coil

Open]

Name.Cur Current actual * CurGain = amps 0 – 3.5 amps

Name.RampCur Current ramped Currend*CurGain= amps 0 – 3.5 amps

Name.CurErr Current Error = RampCur – Cur 16 Signed Integer

Name.CurSumErr Current Error accumulated over time 0 – 65535

Name.CurP Current Proportional Term Constant “P” 0 – 255

Name.CurI Current Proportional Term Constant “I” 0 – 255

Name.MinCurA Minimum Current Coil A *.001 = amps 0 – 3.5 amps

Name.MaxCurA Maximum Current Coil A *.001 = amps 0 – 3.5 amps

Name.Config Configuration Word – Output, Process,

Coil

Output Group Selected as PWM Disabled

Name Description Range

HSEvenName

Set the Bang-bang Coil to On or Off Off, On

HSEven#Name.OpenDisabl

Set the Disable Coil Open Detection 0 [Enabled], 1 [Disabled]

HSEven#Name.Short

Get the Coil Flag for Short Status Off [Coil Ok], On [Coil

Short]

HSEven#Name.Open Get the Coil Flag for Open Status Off [Coil Ok], On [Coil

Open]

HSOddName Set the Bang-bang Coil to On or Off Off, On

HSOdd#Name.OpenDisabl

Set the Disable Coil Open Detection 0 [Enabled], 1 [Disabled]

HSOdd#Name.Short Get the Coil Flag for Short Status Off [Coil Ok], On [Coil

Short]

HSOdd#Name.Open Get/Set the Coil Flag for Open Status Off [Coil Ok], On [Coil

Open]

Enable Process PI Variables

The Name field is the Low-Side name. The default variable name is replaced with the specified name.

Name Description Range

Name.Setpoint

The desired % set point position for the

output

0 to 100%

Name.Feedback The % feedback position for the output 0 to 100%

Name.ProErr Error = Set point – Feedback 16 bit signed integer

Name.ProSumErr Error accumulated over time 0 – 65535

Name.ProP Process Proportional Term Constant “P” 0 – 255

1 2 ... 48 49 50 51 52 53 54 55 56 57 58 ... 169 170

Kommentare zu diesen Handbüchern

Keine Kommentare

High-country-tek DVC80 Bedienungsanleitung Seite 53

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren High-country-tek DVC80